Q32編履式拋丸進行清潔機

◆物料顯著特點 Product features

本固定式、履帶式拋丸機廠家符合多品系，大中批量化生產制造鋁件的從表面防銹或拋丸強化，保養鋁件須得都是不怕有種碰撞的的單重在150kg如下的鑄件及熱處置件，機用戶既可電腦單機適用，又可配線適用. 都屬于鍛造機械裝備區間。

會手動：將產品加進產品履帶輥子中，工作相關人員按著“作業”按鍵，拋丸室門氣動式關掉，拋丸快速去除著手，履帶的向前作業，產品連續一次又一次確定翻滾，大力拋丸器將拋丸快速路拋射進也正在翻滾的產品接觸面上，產品可已經光滑地取得快速去除。鋼丸借助履帶有的溜孔流往回旋運送機，再將鋼丸運送達斗式提拔機，經斗式提拔機提拔到離心過濾器原理，被離心分離處理后存放待會兒用。拋丸結束之后，拋丸室門會手動來，履帶改變方向，將產品卸出。

全自動：該機型是靈活運用高速的傾動的離心葉輪將彈丸拋向履帶內連續性滑動的軸類零件上，然而可達到保養軸類零件的作用。它可代替各業業中的大中型鑄件、鍛件、機加工件、小齒輪、拉簧等件的清砂、噴砂除銹、去硫化皮和表面能武器鍛造。該生產設備不是體化內地外技能，設定聯合開發的新物品，不是種保養轉化率好、節構緊促、噪聲污染小、一整套的性好的保養生產設備。

This machine is suitable for various  large and medium-sized batch production of workpiece surface derusting or peen-forming strengthening, clean up the work-piece must be not afraid of the collision of the single is is 150 kg of the casting and heat treatment, the machine can not only a single use, and wiring use. Belong to casting machinery.

Automatic: the workpiece in rubber crawler roller, the operating personnel press "run" button,  shot room door close behind, pneumatic blast cleaning began to run forward, tracked, workpiece constantly, efficient and powerful shot peen-forming high-speed mixer trajectory to is back on the surface of workpiece, workpiece can completely evenly clear. Steel shot through the crawler sneak into the hole, then screw conveyor will be sent to the steel shot a hoist, a type of the hoist to ascend to the separator, separated by storage to use. Is shot ended, is shot room door open automatically, tracked reversal, discharged the workpiece.

Manual operation: This machine uses high-speed rotary projectile impeller will throw to turn over the workpiece in continuous caterpillar, so as to achieve the purpose of cleaning up the workpiece. It is used in the industries of small-sized castings, forgings, stamping, gear, springs, and a rust-removing, derusting, to oxide skin and surface strengthening. This machine is comprehensive technology, the development of domestic and foreign design new products, it is a kind of cleaning efficiency high, compact structure, the noise is small, systematic good cleaning equipment.

◆廠品作用 Product features

1.該設備主要包括了懸臂離心法式拋丸器，極具操作時間長和節構比較簡單等顯著特點。

2.使用BE型拆分器，兼有積極態度的拆分成效和分娩率，對加快嫩葉有積極態度的用途。

3.分為袋式布袋脈沖除塵器，灰塵進行排放濃度值最低發達國家相關規定的要求，大山河解決了方法者的勞作生態。

4.用于耐腐蝕硅橡膠履帶，消減了對產品工件的碰撞檢測及損害前提，降低了了機械的的噪音。

1. The machine adopts the cantilever centrifugal peen-forming device, with long service life and simple structure.

2. The BE separator has the good separation results and higher productivity, which has positive effec to the blade.

3. The bag filter, dust emission concentrations below the standards prescribed by the state, have greatly improved operator working environment.

4. The wear-resisting rubber crawler, less on the collision and damage, reduce the noise of the machines.

◆適用于條件 Applicable scope

      壓鑄件、精密制造鑄造鑄件、精密制造鑄造鍛件等的消除、光飾。我們要除熱處里件、鑄件、鍛件的從表面陽極氧化皮。彈簧片的突破。立即擰緊件除銹防銹和前處里。

1、參照物英國八十五年間末的噴砂機展開國產系列化開發。

2、進行直聯強力拋丸器，分享利用率好，拋丸量大。

3、風選分離出來法器、丸砂分離出來法率大過99%。

4、彈丸遍及平均，無拋丸方位。

5、耐磨性件便用使用期長，根換及時。

6、機械設備低噪音程序運行。

7、不間斷進行繼電商（或PLC）把控好，把控好柜、聲光電報警信號試驗裝置，PC利用三凌品牌標志標志，具體原器材利用PLC全資品牌標志標志運營簡簡單單、可信度。

Die casting, precision casting, precision forging of cleaning, light ornaments. Remove heat-treated pieces, castings, forgings surface oxide skin. The  strengthening of the spring. Fasteners derusting and former processing.

1. Reference to Germany at the end of the ninety’s shot used the machine manufacturing.

2. The efficient direct coupling strength is shot, transfer the high efficiency, is shot amount is large.

3. Efficient wind separator, pill isolating rate of more than 99% of sand.

4. Projectile enclothe even, without peen-forming blind angle.

5. Wear parts of long service life, change quickly.

6. Low noise operation.

7. Electrical use relay (or PLC) control, control cabinets, sound and light alarm device, PC using mitsubishi brand,mainly by Siemens brand original device operation is simple, reliable joint venture.

◆通常技術水平指標 Main technical parameters